Air Pipe Size Calculator for Compressed Air

Estimate the internal bore needed for a compressed-air flow path in Qatar or the UAE. Enter compressor free-air delivery, inlet gauge pressure, the route length and your pressure-drop target. The result is a preliminary hydraulic estimate. Match it to the actual internal bore and pressure-temperature rating of the complete pipe and fitting system before procurement.

Enter verified manufacturer data, such as a product name followed by its actual internal bore. The material name alone does not establish bore or pressure rating. The aluminium option uses SecureAir catalogue bores by default; stainless steel needs a verified bore list. A custom list is a generic hydraulic reference and does not verify a system rating.

How to use the air pipe size calculator

Use the compressor nameplate or a measured operating demand to establish free-air delivery, often abbreviated to FAD. Enter the amount of air that must pass through the section being assessed, rather than the compressor motor power. A receiver, several compressors and simultaneous machine use can make peak section demand different from the capacity of one compressor. Agree the operating case before choosing pipe.

Enter inlet pressure as gauge pressure. The tool converts it to absolute pressure by adding an atmospheric assumption of 1.01325 bar. Choose bar(g) or psi(g) consistently. The pressure-drop target is always entered in bar. The default 0.1 bar is a planning target for the distribution pipe, not a universal code limit or an allowance for the whole compressed-air installation.

Measure the relevant flow path, then add fitting equivalent lengths from the selected system's engineering data. The fitting field starts at zero so that no hidden allowance changes the answer. Zero does not mean fittings have no loss. Include bends, tees, valves and other restrictions in the design using appropriate manufacturer information.

Calculation method and assumptions

The pressure-drop estimate uses the empirical compressed-air pipe-sizing equation published in the Atlas Copco Compressed Air Manual. In the equation below, q is FAD in litres per second, L is effective path length in metres, d is actual internal bore in millimetres, and p is inlet absolute pressure in bar. The result Δp is in bar.

Δp = 450 × q^1.85 × L ÷ (d^5 × p)

Minimum d = [450 × q^1.85 × L ÷ (allowed Δp × p)]^0.2

The estimate responds to pressure, demand, path length and allowable drop. It does not model a full ring network, equipment losses, changing temperature, pulsation or aged internal surfaces. It does not check the assembled system's mechanical pressure rating.

This empirical equation does not model material roughness separately. Material selection affects the reference size catalogue and application checks. The GI/steel option can select nominal DN labels from EN 10255 medium reference bores. Those dimensions are examples of a defined pipe series, not confirmation of Aamtron stock. The aluminium option uses the actual SecureAir internal bores shown below; stainless steel requires a verified product bore list. These are hydraulic reference matches, not approved material selections.

SecureAir catalogue bore references

The aluminium option matches the calculated minimum to the following actual internal diameters. The hydraulic formula remains the Atlas Copco empirical method, separately sourced from these catalogue dimensions.

SecureAir catalogue pipe table, image page 08 — reference range, not confirmed stock
Internal bore mmOutside diameter mm2.90 m code5.80 m code
2022.7AP203AP206
2527.8AP253AP256
4043.5AP403AP406
5053.9AP503AP506
6367.7AP633AP636
8084.9AP803AP806
100105.3AP1003AP1006
150155.7AP1503AP1506
200206.3AP2003AP2006

The catalogue states a 16 bar maximum operating pressure, without specifying the pressure basis or temperature envelope on the inspected section. Manufacturer confirmation is required for the complete selected system. As a conservative display policy, default SecureAir current and future product suggestions are withheld whenever gauge input plus the 1.01325 bar atmospheric assumption reaches 16 bar. This display policy is not a verified pressure rating or derating, and a selection below it does not establish mechanical suitability.

At the worked 100 CFM duty, ID 40 mm (OD 43.5 mm; AP403 / AP406) is the hydraulic reference. At 125% flow the minimum is approximately 40.28 mm, selecting the next listed ID 50 mm reference. Confirm all pressure-temperature and joint limits separately. View the source catalogue.

Worked example for 100 CFM

Consider a planning example with 100 CFM FAD, a 100 m effective path, 7 bar(g) inlet pressure and 0.1 bar allowable pipe drop. This is a calculation example, not a completed Aamtron project. The converted flow is 47.195 l/s and the absolute inlet pressure is 8.01325 bar. The calculated minimum internal bore is approximately 37.09 mm.

If a proposed pipe has an actual 40 mm internal bore, the estimated drop is approximately 0.0685 bar. A product labelled 40 mm may describe its outside diameter rather than its internal bore, so that label alone is insufficient. The 25% growth calculation repeats the estimate at 125 CFM. A catalogue option must meet that future bore requirement as well as the supplier's application limits.

Quick reference for planning bores

The table gives calculated minimum internal bores at 7 bar(g) and a 0.1 bar pipe-drop target. Length means effective flow-path length, including the fitting allowance. The values are not nominal purchasing sizes or a SecureAir product chart.

Calculated minimum internal bores at 7 bar(g), target 0.1 bar
FAD CFM50 m bore mm100 m bore mm200 m bore mm
5024.9828.7032.96
10032.2937.0942.60
25045.3252.0559.80
50058.5667.2777.28

Why pipe size matters

A narrow pipe can consume more of the available pressure between the compressor room and the user. Raising compressor discharge pressure to overcome avoidable distribution losses can increase energy use. Check the actual load profile, controls and compressor performance before estimating financial savings. No savings percentage follows automatically from this calculator.

An unnecessarily large pipe also costs money and can complicate supports, valves and installation. Compare a technically adequate current size with a realistic expansion allowance. Investigate filters, dryers, hoses, quick couplings and regulators separately; a larger main will not remove a restriction in a machine connection or a blocked filter.

Ring mains and material selection

A ring main can feed users through more than one route, but the split depends on the network and demand locations. Do not automatically halve the flow or enter the full perimeter as one equivalent straight run. Assess the critical operating cases and isolated sections. Where a shutdown closes one side of the ring, the remaining flow path may govern the required size.

Compare aluminium, GI and stainless steel using the full system specification. Obtain the manufacturer's actual bores, joint restrictions, fitting data, pressure-temperature limits and installation instructions. Air purity depends on generation, drying, filtration, storage, distribution condition and measurement at the agreed point of use. Pipe material alone does not establish an ISO 8573-1 class.

Frequently asked questions

What size pipe do I need for 100 CFM?

It depends on pressure, effective path length and the allowed drop. The worked example above needs about 37.09 mm minimum internal bore at 7 bar(g) over 100 m with a 0.1 bar target.

What does CFM mean in piping?

CFM means cubic feet per minute. This calculator expects free-air delivery, not the smaller actual volume occupied by compressed air inside the operating pipe.

What is the maximum acceptable pressure drop?

The acceptable loss depends on the system and equipment. The editable 0.1 bar default is a pipe-distribution planning target. Agree the full system budget with the equipment requirements and designer.

Does changing pressure change the result?

Yes. The calculation uses absolute inlet pressure. Keep the gauge unit correct and verify the result against the selected product's mechanical limits.

Are nominal size and internal bore the same?

No. Nominal DN labels and outside-diameter labels do not state the actual flow bore. Wall thickness and product construction determine internal diameter.

How are bends and valves included?

Add appropriate fitting equivalent lengths in the same length unit as the route. Obtain those values from the selected system supplier or the designer's documented method.

How does the tool allow for future expansion?

It repeats the hydraulic calculation at 125% of the entered FAD. Where a verified size catalogue is available, it also chooses a larger catalogue size meeting that future duty.

Can I use the result directly for installation?

Use it for preliminary planning. Final selection needs verified product bores and ratings, fittings, supports, network operating cases, equipment losses and the project's design requirements.

Share or embed this calculator

Add the tool to a website using the Aamtron calculator widget and embed instructions. The widget uses the same sizing engine and calculates locally in the visitor’s browser.

Share a sizing enquiry

Include the selected units, flow, gauge pressure, route length and fitting allowance when you contact the project team. Save the calculator URL with your project notes so the estimate can be reviewed against the actual system specification.

Discuss a compressed air piping project in Qatar or send your layout, demand and operating pressure to Aamtron's engineering team. For UAE installation planning, use the UAE piping services page.

Qatar UAE WhatsApp